Annihilate
发表于 2025-3-21 18:42:07
书目名称CNC Part Programming Workbook影响因子(影响力)<br> http://impactfactor.cn/if/?ISSN=BK0220378<br><br> <br><br>书目名称CNC Part Programming Workbook影响因子(影响力)学科排名<br> http://impactfactor.cn/ifr/?ISSN=BK0220378<br><br> <br><br>书目名称CNC Part Programming Workbook网络公开度<br> http://impactfactor.cn/at/?ISSN=BK0220378<br><br> <br><br>书目名称CNC Part Programming Workbook网络公开度学科排名<br> http://impactfactor.cn/atr/?ISSN=BK0220378<br><br> <br><br>书目名称CNC Part Programming Workbook被引频次<br> http://impactfactor.cn/tc/?ISSN=BK0220378<br><br> <br><br>书目名称CNC Part Programming Workbook被引频次学科排名<br> http://impactfactor.cn/tcr/?ISSN=BK0220378<br><br> <br><br>书目名称CNC Part Programming Workbook年度引用<br> http://impactfactor.cn/ii/?ISSN=BK0220378<br><br> <br><br>书目名称CNC Part Programming Workbook年度引用学科排名<br> http://impactfactor.cn/iir/?ISSN=BK0220378<br><br> <br><br>书目名称CNC Part Programming Workbook读者反馈<br> http://impactfactor.cn/5y/?ISSN=BK0220378<br><br> <br><br>书目名称CNC Part Programming Workbook读者反馈学科排名<br> http://impactfactor.cn/5yr/?ISSN=BK0220378<br><br> <br><br>
思想上升
发表于 2025-3-21 23:13:41
Work holding and tooling, component and therefore to the clamping/holding devices. As the programmer, it is part of your task to decide what type of work-holding device is required for a particular operation. The following conditions must be met:
伴随而来
发表于 2025-3-22 02:44:48
Toolpath calculations,der to machine the required shape. These calculations may be needed to determine the intersect points of arcs and lines, arc centres and tangency points of lines on arcs or circles, and so on. If you are going to write programs manually, you will need a good knowledge of mathematics, trigonometry an
主讲人
发表于 2025-3-22 05:06:49
http://reply.papertrans.cn/23/2204/220378/220378_4.png
Cpr951
发表于 2025-3-22 09:58:45
http://reply.papertrans.cn/23/2204/220378/220378_5.png
重力
发表于 2025-3-22 14:13:16
Using a drawing package,, tangents between circles, arcs through a point tangential to a line and so on. The main difference is in the way that you construct the geometry, since you only need to draw details like the profile shape or the hole positions. You do not have to incorporate features like hatching lines, dimension
重力
发表于 2025-3-22 19:59:59
http://reply.papertrans.cn/23/2204/220378/220378_7.png
取回
发表于 2025-3-22 23:14:09
Machining pockets,ate on a pull-down menu system which requires the name of the previously defined pocket shape and the name of each ‘island’ within the pocket. Or a pocket clearance routine within the software may be used to define the shape of the pocket, including ‘islands’. In either case, the data entered is use
易达到
发表于 2025-3-23 04:52:45
http://reply.papertrans.cn/23/2204/220378/220378_9.png
Console
发表于 2025-3-23 05:41:41
Complex profile with a spline,-ordinates are tabulated at the top left-hand corner of the drawing, thus avoiding a mass of dimension lines. A spline (a series of points through which a smooth curve is drawn) is shown along the top edge of the component. Consult your manual and research the commands that your CAD/CAM system uses