Enkephalin
发表于 2025-3-21 19:31:46
书目名称Industrial Measurements in Machining影响因子(影响力)<br> http://figure.impactfactor.cn/if/?ISSN=BK0464049<br><br> <br><br>书目名称Industrial Measurements in Machining影响因子(影响力)学科排名<br> http://figure.impactfactor.cn/ifr/?ISSN=BK0464049<br><br> <br><br>书目名称Industrial Measurements in Machining网络公开度<br> http://figure.impactfactor.cn/at/?ISSN=BK0464049<br><br> <br><br>书目名称Industrial Measurements in Machining网络公开度学科排名<br> http://figure.impactfactor.cn/atr/?ISSN=BK0464049<br><br> <br><br>书目名称Industrial Measurements in Machining被引频次<br> http://figure.impactfactor.cn/tc/?ISSN=BK0464049<br><br> <br><br>书目名称Industrial Measurements in Machining被引频次学科排名<br> http://figure.impactfactor.cn/tcr/?ISSN=BK0464049<br><br> <br><br>书目名称Industrial Measurements in Machining年度引用<br> http://figure.impactfactor.cn/ii/?ISSN=BK0464049<br><br> <br><br>书目名称Industrial Measurements in Machining年度引用学科排名<br> http://figure.impactfactor.cn/iir/?ISSN=BK0464049<br><br> <br><br>书目名称Industrial Measurements in Machining读者反馈<br> http://figure.impactfactor.cn/5y/?ISSN=BK0464049<br><br> <br><br>书目名称Industrial Measurements in Machining读者反馈学科排名<br> http://figure.impactfactor.cn/5yr/?ISSN=BK0464049<br><br> <br><br>
overbearing
发表于 2025-3-21 23:52:09
http://reply.papertrans.cn/47/4641/464049/464049_2.png
Sarcoma
发表于 2025-3-22 03:52:07
978-3-030-49909-9Springer Nature Switzerland AG 2020
SUGAR
发表于 2025-3-22 08:12:15
http://reply.papertrans.cn/47/4641/464049/464049_4.png
HALL
发表于 2025-3-22 11:14:05
Grzegorz M. Królczyk,Piotr Niesłony,Jolanta KrólczDescribes new theories in machining and metrology.Discusses a number of theoretical and experimental issues.Reports on emerging optimization and control methods
EVADE
发表于 2025-3-22 16:47:10
http://reply.papertrans.cn/47/4641/464049/464049_6.png
受伤
发表于 2025-3-22 17:03:34
Mathematical Modelling of Core Roughness Depth During Hard Turning,ter and coefficient . obtained from the ratio between . and the sum of . and .. According to the obtained mathematical models, 3D graphs of the dependences between the . parameter, coefficient . and the input independent variables are also shown. The obtained mathematical models are explained, and a
学术讨论会
发表于 2025-3-23 00:03:04
http://reply.papertrans.cn/47/4641/464049/464049_8.png
malapropism
发表于 2025-3-23 01:55:04
The Surface Texture of Ti6Al4V Titanium Alloy Under Wet and Dry Finish Turning Conditions,e cutting speed and feed rate influence are lower in comparison with wet turning. Compared to wet machining, a higher number of surface defects caused by adhesive bonds were observed under dry turning. Favorable values of roughness parameters were obtained using middle cutting speeds and feed rates
省略
发表于 2025-3-23 06:27:18
http://reply.papertrans.cn/47/4641/464049/464049_10.png