吸收
发表于 2025-3-21 18:56:38
书目名称Advances in Manufacturing Engineering and Materials影响因子(影响力)<br> http://figure.impactfactor.cn/if/?ISSN=BK0148726<br><br> <br><br>书目名称Advances in Manufacturing Engineering and Materials影响因子(影响力)学科排名<br> http://figure.impactfactor.cn/ifr/?ISSN=BK0148726<br><br> <br><br>书目名称Advances in Manufacturing Engineering and Materials网络公开度<br> http://figure.impactfactor.cn/at/?ISSN=BK0148726<br><br> <br><br>书目名称Advances in Manufacturing Engineering and Materials网络公开度学科排名<br> http://figure.impactfactor.cn/atr/?ISSN=BK0148726<br><br> <br><br>书目名称Advances in Manufacturing Engineering and Materials被引频次<br> http://figure.impactfactor.cn/tc/?ISSN=BK0148726<br><br> <br><br>书目名称Advances in Manufacturing Engineering and Materials被引频次学科排名<br> http://figure.impactfactor.cn/tcr/?ISSN=BK0148726<br><br> <br><br>书目名称Advances in Manufacturing Engineering and Materials年度引用<br> http://figure.impactfactor.cn/ii/?ISSN=BK0148726<br><br> <br><br>书目名称Advances in Manufacturing Engineering and Materials年度引用学科排名<br> http://figure.impactfactor.cn/iir/?ISSN=BK0148726<br><br> <br><br>书目名称Advances in Manufacturing Engineering and Materials读者反馈<br> http://figure.impactfactor.cn/5y/?ISSN=BK0148726<br><br> <br><br>书目名称Advances in Manufacturing Engineering and Materials读者反馈学科排名<br> http://figure.impactfactor.cn/5yr/?ISSN=BK0148726<br><br> <br><br>
filial
发表于 2025-3-21 21:35:15
Research on Water Jet Cutting of Polymer Composites Based on Epoxy/Waste Fibres from Coconut Process978-0-230-22309-7
小教堂
发表于 2025-3-22 01:07:05
Effect of Frequency Change During Pulsed Waterjet Interaction with Stainless Steel978-0-230-50489-9
LAVA
发表于 2025-3-22 05:35:14
http://reply.papertrans.cn/15/1488/148726/148726_4.png
Outspoken
发表于 2025-3-22 10:10:55
Comparison of Non-destructive Sensing Methods on Surface Created by Waterjet Technology
追踪
发表于 2025-3-22 15:09:38
Investigation of Limestone Cutting Efficiency by the Abrasive Water Suspension Jet
Rct393
发表于 2025-3-22 20:20:52
http://reply.papertrans.cn/15/1488/148726/148726_7.png
overwrought
发表于 2025-3-23 00:49:28
http://reply.papertrans.cn/15/1488/148726/148726_8.png
finite
发表于 2025-3-23 03:43:50
Yonghua Xie,Xiaoyong Kou,Ping Li,Xiaolong Xusis proved that a considerable destruction of the material occurred at the water jet outlet, i.e. on a bottom side of the cut, under unsuitable cutting conditions and at an absence of the abrasive grains which is an undesirable factor for following applications of these materials.
同来核对
发表于 2025-3-23 09:33:40
https://doi.org/10.1007/978-3-030-48513-9 results concluded that for intermediate values of standoff distance (3–4 mm) and higher fluid pressure (13–16 MPa), deeper grooves were observed. Deepest mean groove observed within the experimental domain was of 183 µm deep at 2 mm standoff distance and 16 MPa fluid pressure. The experiments concl