仲裁者
发表于 2025-3-25 05:46:34
http://reply.papertrans.cn/63/6285/628452/628452_21.png
过于平凡
发表于 2025-3-25 10:30:27
http://reply.papertrans.cn/63/6285/628452/628452_22.png
逢迎白雪
发表于 2025-3-25 12:14:10
Design of Magnetic Aluminium (A356) Based Composites through Combined 2 Method of Sinter + Forging powder metallurgy and thixoforming (sinter + Forging). Three different reinforcements (Magnetic iron oxide, Fe.O. – Hybrid graphene nano-platelets, GNPs, Nickel, Ni) were used and preceded under the constant process parameters such as hot compaction, sinter-forging, sintering time, etc. Mechanical a
Tartar
发表于 2025-3-25 18:12:26
Design of Low Composites from Recycled Copper + Aluminium Chips for Tribological Applications,designed through combined method of powder metallurgy and sinter + Forging. First of all, Al-Cu matrix was doped with ZnO after the ball milling with two basic reinforcements (Nb.Al– SiC, etc.) was carried out during the 4 h. A basic composition was prepared depending on the doping percentage of ZnO
MERIT
发表于 2025-3-25 22:35:50
Liquid Metal Dispersions for Stretchable Electronics,se dispersions are of particular interest for electronically conducting polymer applications where the combined mechanical and electrical performance of the material is important, especially in the presence of large deformations. A key weakness of these systems, however, is apparent in soft polymer
chalice
发表于 2025-3-26 01:56:30
Laser Cutting of the TiN +Al2O3 Reinforced Aluminium Matrix Composites Through Semisolid Sintering,e cutting in the metals used in manufacturing engineering. In the present work, laser cutting process of aluminium matrix composites obtained from scrap chips reinforced with hard ceramics (TiN + Al.O.) were carried out. They are being widely used in the aerospace and automobile industries such as a
矿石
发表于 2025-3-26 08:18:10
Optimization of Laser Cutting Parameters for Tailored Behaviour of Scrap (Ti6242 + Ti) Based Composs frequently used for manufacturing of composites as an advance machining process. It is suitable for geometrically complex profile cutting in the metals used in manufacturing engineering. In the present work, laser cutting process of scrap titanium matrix composites obtained from scrap (Ti6242 + pu
无效
发表于 2025-3-26 11:47:52
Studying Effect of CO2 Laser Cutting Parameters of Titanium Alloy on Heat Affected Zone and Kerf Wit edges are affected by cutting parameters as well as the work-piece material. In this paper CO. laser cutting of 3 mm thick of Titanium alloy sheet grade 5 Ti-6Al-4 V is investigated. The main objectives of the present work are firstly focused on evaluating the effect of laser power (.), cutting sp
extinct
发表于 2025-3-26 15:22:16
Fatigue Characterization of In-Situ Self-Healing Dental Composites,ing and thermal loads, and the damage due to fatigue loads plays a major role in restorative failures in the form of cracks. A lab-based fatigue test is a suitable technique to characterize the crack propagation in dental composites. In this paper, we investigate the ability of a self-healing materi
Canary
发表于 2025-3-26 19:05:17
Effect of Process Induced Stresses on Measurement of FRP Strain Energy Release Rates,ve cured composites, this interface typically forms at an elevated temperature that can be quite different from the part’s service temperature. As a result, matrix shrinkage and CTE mismatch can produce significant residual stresses at this bi-material interface. This study shows that the measured c