Lincoln
发表于 2025-3-21 16:32:49
书目名称Materials Design and Applications III影响因子(影响力)<br> http://figure.impactfactor.cn/if/?ISSN=BK0625769<br><br> <br><br>书目名称Materials Design and Applications III影响因子(影响力)学科排名<br> http://figure.impactfactor.cn/ifr/?ISSN=BK0625769<br><br> <br><br>书目名称Materials Design and Applications III网络公开度<br> http://figure.impactfactor.cn/at/?ISSN=BK0625769<br><br> <br><br>书目名称Materials Design and Applications III网络公开度学科排名<br> http://figure.impactfactor.cn/atr/?ISSN=BK0625769<br><br> <br><br>书目名称Materials Design and Applications III被引频次<br> http://figure.impactfactor.cn/tc/?ISSN=BK0625769<br><br> <br><br>书目名称Materials Design and Applications III被引频次学科排名<br> http://figure.impactfactor.cn/tcr/?ISSN=BK0625769<br><br> <br><br>书目名称Materials Design and Applications III年度引用<br> http://figure.impactfactor.cn/ii/?ISSN=BK0625769<br><br> <br><br>书目名称Materials Design and Applications III年度引用学科排名<br> http://figure.impactfactor.cn/iir/?ISSN=BK0625769<br><br> <br><br>书目名称Materials Design and Applications III读者反馈<br> http://figure.impactfactor.cn/5y/?ISSN=BK0625769<br><br> <br><br>书目名称Materials Design and Applications III读者反馈学科排名<br> http://figure.impactfactor.cn/5yr/?ISSN=BK0625769<br><br> <br><br>
减震
发表于 2025-3-21 22:02:00
http://reply.papertrans.cn/63/6258/625769/625769_2.png
文艺
发表于 2025-3-22 04:24:54
http://reply.papertrans.cn/63/6258/625769/625769_3.png
镀金
发表于 2025-3-22 08:36:12
Multiscale Modeling for Residual Stresses Analysis of a Cast Super Duplex Stainless Steelwork addresses the effect of distribution and volume fraction of phases on the magnitude and gradient of residual stresses on a cast SDSS specimen. The numerical method for the homogenization of the material properties is also addressed. The procedure followed consisted of modeling the microstructur
languor
发表于 2025-3-22 09:26:35
Phono-Absorbent Behavior of New Fiberglass Plates from Mixed Plastic Material Wastesavior of the obtained plates was analyzed to define the possibility of using them for the reduction of the environmental noise. The data obtained was analyzed, and the results were compared with the characteristics of other materials which could be replaced by this new material.
expdient
发表于 2025-3-22 16:29:35
http://reply.papertrans.cn/63/6258/625769/625769_6.png
说笑
发表于 2025-3-22 20:29:04
http://reply.papertrans.cn/63/6258/625769/625769_7.png
GUILT
发表于 2025-3-22 22:36:29
http://reply.papertrans.cn/63/6258/625769/625769_8.png
LIMN
发表于 2025-3-23 03:40:24
http://reply.papertrans.cn/63/6258/625769/625769_9.png
Ambiguous
发表于 2025-3-23 06:49:58
Machinability Study of Polymeric Parts Fabricated by Additive Manufacturing Under a Dry Milling Procerence purposes. With cutting speed, feed rate and cut depth as the process parameters, 13 terns were formed. Milling processes were executed on 30 x 30 x 10 mm block-shaped 3D prints and surface roughness values were obtained via a portable roughness tester. It was found that the most influential p